Expert Answers about GMC Lift Supports

• What Replacement Glass Hatch Rear Support Fits My 2011 Honda Pilot?
• I have the right replacement part you need. I went ahead and did research on your 2011 Honda Pilot's lift supports. From my available research, there are three different types of replacement supports: the back glass support, the hatch lift support, and the front hood support. Unfortunately, the Hood Lift Support - Custom Fit # ATL34TR is the replacement in the hood area of some models of Honda Pilots. This is a completely different part than you need. For the glass portion of your rear...
  view full answer...


• What is the Difference Between Lift and Support Capacity on a Trailer Jack
• The support capacity is how much a jack can hold whereas the lift capacity is how much a jack can lift. The Bulldog Square Jack w/ Footplate part # BD190754 has a 8,000 lb support and 5,000 lb lift capacity. If you will be using the jacks to lift and lower a trailer onto a hitch ball or kingpin then they will need to be chosen according to their lift capacity but if you are just using them to stabilizer or support a trailer then they can be chosen according to their support capacity. Generally...
  view full answer...


• Force Rating for LS10602 Atlas Lift Hood Lift Support
• The force rating for the Hood Lift Support # ATL32QR is 78 lbs according to my contact at Atlas Lift.
  view full answer...


• Is There A Maximum Distance That Motorhome Wheels Can Hang With Air Lift Air Springs Installed
• Air Lift LoadLifter 5000 Ultimate Air Helper Springs with Internal Jounce Bumpers # AL88240 require that the axles be supported at all times, otherwise the weight could rip the bellows from the brackets. If you used leveling jacks to lift the frame of the motorhome you would need to place a support under the wheels as well, like leveling blocks # UF48-979051. Air Lift has stated that they offer cradles that will attach the lower bracket to help support the springs, so you could also reach...
  view full answer...


• Can Vehicle With Air Helper Springs Be Serviced on a Lift
• Air Lift and Firestone use different methods of attaching the air springs to the metal plates. Firestone uses a crimp roll design that's very strong, strong enough to handle the weight of the axle. If the vehicle will be lifted by the frame, you'll want to deflate Firestone air springs like # F2525 so they can extend to their maximum length without being damaged. It's not necessary to support the axle. Air Lift helper springs like the # AL88200 you'd looked at use a band clamp design that's...
  view full answer...


• Can I Lift Vehicle Without Supporting Firestone Air Springs?
• When air bags are installed, you usually need to support the rear axle when the vehicle is hoisted. Now, Firestone is actually really proud of their air springs design since they use technology from their heavy truck Airide springs and these can withstand thousands of pounds of pulling force without damage. As for the hardware, that's made to support the air springs. As long as they were installed correctly, they will be able to hold while the vehicle is lifted. Also, when you vehicle...
  view full answer...


• Will Air Lift LoadLifter 7500 XL Air Helper Springs Fit 2008 Dodge Ram 3500 with Lift Kit
• The Air Lift LoadLifter 7500 XL Air Helper Springs # AL57595 will fit about a 1" block lift on their own. If you have a lift higher than that for your 2008 Dodge Ram 3500 then you need to add some spacers to accommodate your lift. Spacers are offered in a 2" # AL52420 and 4" # AL52440 option depending on how much of a lift you have. These can support up to 7,500 lbs so if you are towing a 14,000 lb trailer you will have support for the first 7,500 lbs. Please note that suspension enhancement...
  view full answer...


• Can Gate King Adjustable Tailgate Support Bars GK74FR Lock The Tailgate In Flat Position?
• The Adjustable Tailgate Support Bars # GK74FR does not lock the tailgate down in the flat position. When the latching pins are engaged and the tailgate is lifted, the support bars will lock into the first position and so on. This will keep the tailgate from dropping all the way down and it will stay in that locked position until lifted up. This will not stop the tailgate from lifting up as you can simply lift the tailgate to lock it into the next catch position. I attached a helpful demonstration...
  view full answer...


• Jacks to Lift a Truck Bed Camper Out of a Truck Bed
• Jack-in-a-Box Camper Slide-Out Support Set # JB-20 was designed to support slide outs. What you are looking for is a truck bed camper jack. We have several, see link, ranging from 1,000 to 4,000 pounds capacity and max lift height from 57 to 67 inches. The highest capacity models are # CXHD and # CX74 at 4,000 pounds at 57 or 67 inches lift height, respectively.
  view full answer...


• Is Atlas Lift Tailgate Lift Support Meant for Rear Hatch or Back Glass
• The Tailgate Lift Support # ATL82GR will only work for the rear hatch of the 2007 Toyota Matrix. The back glass uses a different strut.
  view full answer...


• Gen-Y Hitch Loading Ramps # 325-GH-R96 for a 5,000 lb Scissor Lift
• Each ramp included with the Gen-Y Hitch Aluminum Loading Ramp Set # 325-GH-R96 can support up to 5,000 lbs each for a total of 10,000 lbs when the equipment being loaded is supported by both ramps. This weight capacity will be more than enough to use with your 5,000 lb scissor lift as long as you are able to use both ramps to support the weight of the scissor lift. Of course, your trailer will also need to be rated high enough to handle the 5,000 lb scissor lift. Check out the video linked...
  view full answer...


• Correct Liftgate Lift Support for a 1997 Toyota 4Runner
• The correct Liftgate Lift Support for a 1997 Toyota 4Runner is part # ATL98VR.
  view full answer...


• Do The Firestone Ride-Rite Air Helper Springs Need Disconnected Before Lifting On Vehicle Lift?
• The Firestone Ride-Rite Air Helper Springs # F2245 for your 2003 Toyota Tundra are safe to use with a vehicle lift. You will not need to support the axle or disconnect the air springs to use on a lift. Firestone uses a wire girdle and roll crimps their air springs to the mounting plates which are capable of supporting the weight of the axle hanging when put on a vehicle lift.
  view full answer...


• Tailgate Lift Assist That Will Fit With a Gate King Tailgate Support on a 2017 Ford F-250
• The Hopkins EasyLift Tailgate Lift Assist # 74211 is a universal lift that will fit with a set of Gate King Adjustable Tailgate Support Bars # GK74FR on your 2017 Ford F-250. The EasyLift is a universal part that will fit most all trucks. It does require the drilling of two holes to fit. One hole in the bottom of the tailgate and the second hole in the drivers side bedside upright that the tailgate is mounted to.
  view full answer...


• Can Trailer Stabilizer Scissor Jacks be Used to Lift a Trailer
• Scissor jacks for trailers such as # TJSCHD-24 are used for support but not lifting applications. For lifting I recommend using a bottle jack such as # ALL620471 and then using a stabilizer jack to support the trailer at the proper height. Bottle jacks are great since they don't take up a lot of space and still have plenty of capacity.
  view full answer...


• Can Air Lift Air Bags on 2020 Ram 2500 be Used When on Vehicle Hoise
• Your 2020 Ram 2500 can have the Air Lift LoadLifter 5000 Ultimate Air Helper Springs with Internal Jounce Bumpers # AL88289 installed and the vehicle can be on a hoist without the rear axle braced if it is a short term amount of work like a tire rotation, as you mentioned. Otherwise, what is meant by brace is the axle should be supported with jack stands. There are certainly jack stands tall enough that may garages have, and they need to be used if lengthy work is being done and you have...
  view full answer...


• Torklift GlowStep Replacement Support Bracket and Bolt
• I have a solution for you but we don't have a replacement bracket to replace the support and bolt that was broken on your TorkLift GlowStep similar to the # TLA8004 . Instead you would need to use the Add-A-Step for TorkLift GlowStep Revolution Scissor Steps # TLA8101 which will work on any TorkLift GlowStep models with the 25-7/16" wide mounting base. You can use the parts in this kit to replace your broken parts or replace an entire step. If you have the 27-7/16" mounting base model...
  view full answer...


• Will The Air Lift LoadLifter 5,000 Be Damaged On My Vehicle If It Is Put On A Vehicle Lift?
• As long as the rear axle is supported, the Air Lift LoadLifter 5000 Ultimate Air Helper Springs with Internal Jounce Bumpers # AL88289 you should be good. You're also going to want to set your bags to 0 PSI while your truck is being lifted in place, and then when the truck is in place you're going to want to support the rear axle.
  view full answer...


• Recommended Stabilizer Support Jack for 40 Foot Trailer When Loading and Unloading
• From your description, it sounds like you need a stabilizer jack like the Stallion Stabilizer Jacks - 7" Drop Leg Travel - 22-1/4" - Qty 2 # 288-01892-2. These jacks are able to be out of the way when not needed and then add 1000 lb capacity support when needed and up to 650 lbs of lift. This will give you the support and stability you desire for loading and unloading. If you need more support then I recommend the Ultra-Fab Ultra Scissor Jacks - 30" Lift - 6,500 lbs - Qty 2 # UF48-979031....
  view full answer...


• Super Springs Suspension Enhancement for 2018 Ram 3500 with Leveling Kit to Give Lift
• The Super Springs kit part # SSA15MTKT is exactly what you'd want as it will give you the support you are needing and will lift the rear suspension to eliminate the sag you are experiencing. When unloaded it will add almost an inch to the rear height on the lowest setting and when towing it will sit level. Higher settings will add more height. The amount of support you want is also adjustable so if you find you want it to sit higher or lower you can easily adjust everything.
  view full answer...